Bambu Lab P1S

Printer

Bambu Lab P1S

4 source-linked failure reports. Most reported: Nozzle clog mushroomed filament above cutter; PTFE tube worn through after 1400+ hours. Typical failure around 5 mo. Median repair $0.

Reliability signal — · Insufficient data · data confidence Very Low

4 confirmed failure reports

Release year: 2023

Reliability summary

What is likely to go wrong, when it happens, and how expensive it can be — from source-linked failure reports. Counts are reports in our database, not a population failure rate. Methodology →

Reliability signal

—

4 confirmed failure reports · Insufficient data · Data confidence: Very Low

Need at least 5 confirmed failure-signal reports before showing an A–F grade.

Most common issue
Nozzle clog mushroomed filament above cutter; PTFE tube worn through after 1400+ hours
Typical first failure
5 mo
Median of confirmed reports with timing
Median repair cost
$0
Reported costs · Mostly Mixed markets
Highest reported repair
$0
Not a quote · costs differ by country

What breaks?

Failure types

Click a type in the reports section below to filter.

  • Nozzle clog mushroomed filament above cutter; PTFE tube worn through after 1400+ hours1 · 25%
  • Chronic under-extrusion after warranty hotend and AMS hub/buffer replacements1 · 25%
  • AMS stopped pushing filament to extruder after ~6 months (all slots)1 · 25%
  • AMS gen1 internal hub feed cover cracked — no filament feed from any slot1 · 25%

When does it break?

Failure timing

Months after purchase, using reports that included timing.

What does it cost?

Reported repair costs

Distribution of owner-reported repair costs (mostly mixed markets)— not a quote or guarantee. Labor and parts prices vary by country.

Median months to failure

5

Failure reports

4

View →

Median repair cost

$0

Still recommend

—

% repaired

66.7%

% mfr warranty

100%

% extended warranty

—

% support helpful

—

Use these reports as a risk signal, then check current listings before you buy.

Search this model on Amazon

As an Amazon Associate, After Warranty may earn from qualifying purchases.

Keep researching

What breaks?

What breaks? · reports

Nozzle clog mushroomed filament above cutter; PTFE tube worn through after 1400+ hours

Hotend / PTFE feed tube

Forum / discussionIndexed Oct 16, 2026Source-linkedVerify source — Reddit post

Reddit r/BambuLab: First major P1S failure after 1400+ hours — near end of a PETG spool the nozzle clogged; drive gear kept pushing and mushroomed filament above the cutter so filament could not retract, requiring near-full toolhead disassembly. Owner also found the PTFE tube to the toolhead almost worn through from rubbing on the top glass.

UnverifiedEvidence ★★★☆☆
View report details

Months until failure

Not stated

Repair cost

Not stated

Repaired

Yes

Manufacturer warranty

Not stated

Extended warranty

Not stated

Support helpful

Not stated

Would recommend

Not stated

AI extraction confidence

90%

Verification status

Unverified

Evidence quality

★★★☆☆ (3/5)

Discussion

Chronic under-extrusion after warranty hotend and AMS hub/buffer replacements

Extruder / hotend thermal path

4 months

$0

Forum / discussionIndexed Oct 16, 2026Cost market · MixedSource-linkedVerify source — Reddit post

Reddit r/BambuLab: New P1S AMS combo (Nov 2025) needed hotend replacement (Jan 2026), then AMS hub + filament buffer replacement (Feb–Mar 2026). Immediately afterward printer fails to extrude enough filament after a few layers despite good grip, cold pulls, multiple hotends, dried filament, and both AMS and external spool. Ongoing Bambu support tickets.

UnverifiedEvidence ★★★☆☆Mfr warranty
View report details

Months until failure

4 months

Repair cost

$0

Repaired

Yes

Manufacturer warranty

Yes

Extended warranty

Not stated

Support helpful

Not stated

Would recommend

Not stated

AI extraction confidence

91%

Verification status

Unverified

Evidence quality

★★★☆☆ (3/5)

Discussion

AMS stopped pushing filament to extruder after ~6 months (all slots)

AMS feed path / hub or buffer

6 months

Forum / discussionIndexed Oct 16, 2026Source-linkedVerify source — Reddit post

Reddit r/BambuLab: P1S + AMS owned ~half a year. During a multicolor print AMS could no longer push filament fully to the extruder on every filament change; owner had to assist manually. Tried PTFE replacement, cleaning gears/hub and canned air with no fix. Commenters report broken AMS hub housings and warranty buffer replacements for the same symptom.

UnverifiedEvidence ★★★☆☆
View report details

Months until failure

6 months

Repair cost

Not stated

Repaired

No

Manufacturer warranty

Not stated

Extended warranty

Not stated

Support helpful

Not stated

Would recommend

Not stated

AI extraction confidence

90%

Verification status

Unverified

Evidence quality

★★★☆☆ (3/5)

Discussion

AMS gen1 internal hub feed cover cracked — no filament feed from any slot

AMS hub / feed cover

Forum / discussionIndexed Oct 16, 2026Source-linkedVerify source — Reddit post

Reddit r/BambuP1S: After ~1000 print hours on a P1S bought in January, AMS suddenly would not feed from any slot. Owner disassembled and found the plastic cover where the four AMS slots merge cracked/broken. Filed a warranty claim.

UnverifiedEvidence ★★★☆☆Mfr warranty
View report details

Months until failure

Not stated

Repair cost

Not stated

Repaired

Not stated

Manufacturer warranty

Yes

Extended warranty

Not stated

Support helpful

Not stated

Would recommend

Not stated

AI extraction confidence

92%

Verification status

Unverified

Evidence quality

★★★☆☆ (3/5)

Discussion

Compare nearby models

Similar products

Stay ahead of failures

Notify me about this model

Get an email when a new source-linked failure report is published for the Bambu Lab P1S.

We only email when a new published report is added for Bambu Lab P1S. No spam, unsubscribe by contacting support.

Contribute signal

Had a failure with this model?

Add your experience and help future shoppers understand what happens after the warranty.

Submit your experience